lelasas.blogg.se - Ai-thinker esp8266 firmware download

#Ai thinker esp8266 firmware download install
#Ai thinker esp8266 firmware download serial
#Ai thinker esp8266 firmware download manual
#Ai thinker esp8266 firmware download software

It can be used to make a call, send text messages. It is a very small module, based on the TI CC chip. I only need to have the coordinates from the GPS. We cannot guarantee the accuracy of company and product information.

#Ai thinker esp8266 firmware download serial

Ai thinker a9 Got the serial port fixed, A7 back in operation. This firmware was graciously supported by DariBer, who had offered me a development bulb.Ai thinker a9.

#Ai thinker esp8266 firmware download software

OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, IN NO EVENT SHALL THEĪUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,įITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR Flash the firmware (board Generic ESP8266 module, Upload Speed 115200 and Flash Size 1M (128K SPIFFS))įOR SECURITY REASONS, IT'S HIGHLY RECOMMENDED TO HAVE A STRONG WI-FI PASSWORD, TO ENABLE TLS, TO DEACTIVATE THE DEBUGGING OUTPUT AND TO SET A PASSWORD FOR OTA.Solder wires from (bulb) 3V3 to 3V3 (FTDI), GND to GND, RX to TX, TX to RX and ÌO0 to GND.Define MQTT_MAX_PACKET_SIZE to 512instead of 128in Arduino/libraries/pubsubclient/src/PubSubClient.h.

#Ai thinker esp8266 firmware download install

Install the external libraries ( PubSubClient, ArduinoJson and my9291).

Define your MQTT settings ( #define MQTT_USERNAME "", #define MQTT_PASSWORD "", #define MQTT_SERVER "" and #define MQTT_SERVER_PORT ).

Define your WiFi SSID and password ( #define WIFI_SSID ""and #define WIFI_PASSWORD ""in config.h).

Install the Arduino IDE and the ESP8266 core for Arduino.

To get this working, discovery: true must be defined in your mqtt configuration in Home Assistant

#Ai thinker esp8266 firmware download manual

This allows for instant setup and use of your device without requiring any manual configuration in Home Assistant. This firmware supports Home Assistant's MQTT discovery functionality, added in 0.40.

When the device successfully connects it will publish alive to that topic and when it disconnects, dead will automatically be published. The firmware will publish a MQTT Last Will and Testament at /rgbw/status.

Gamma correction (enabled, #define GAMMA_CORRECTION in config.h).

Store the current state of the bulb in memory to prevent from losing its state in case of power cut (enabled, #define SAVE_STATE in config.h).

Native support for Home Assistant, including MQTT discovery (enabled, #define MQTT_HOME_ASSISTANT_SUPPORT in config.h).

ArduinoOTA support for over-the-air firmware updates (enabled, #define OTA in config.h).

Debug printing over Telnet or Serial (uncomment #define DEBUG_TELNET or #define DEBUG_SERIAL in config.h).

TLS support (uncomment #define TLS in config.h and change the fingerprint if not using CloudMQTT).

Supports brightness, RGB and white colors, color temperature and effects.

Remote control over the MQTT protocol via JSON.

The bulb is a cheap (~12-18$) product available on sites like Aliexpress ( here) and eBay ( here or here), which can be easily reprogrammed as it is based on the popular ESP8266 Wi-Fi chip. This is an alternative firmware for AI-Thinker RGBW LED bulbs, which uses MQTT instead of the default Chinese mobile application. THIS REPOSITORY IS NOT MAINTAINED ANYMORE, SEE ESPHome AS AN ALTERNATIVE. Alternative firmware for AI-Thinker RGBW bulbs